Simulation Exercise - Structural Boundary Conditions
Download the zip file and extract the contents. Go through the Instructions file. Follow along with the provided steps and solve the model. You can start the quiz after you have obtained a solution.
For performing the simulation, you can use the latest release of the academic, commercial, or free student version of Ansys Mechanical. Ansys Student can be downloaded for free here.
Quiz Summary
0 of 10 Questions completed
Questions:
Information
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading...
You must sign in or sign up to start the quiz.
You must first complete the following:
Results
Results
0 of 10 Questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 point(s), (0)
Earned Point(s): 0 of 0, (0)
0 Essay(s) Pending (Possible Point(s): 0)
Categories
- Not categorized 0%
-
Unfortunately, you did not pass the quiz.
Don't be discouraged - Go through the course material including the lecture videos, handout slides, and simulation examples to prepare and try again.
-
Congratulations, you have passed the quiz!
You still have room for improvement - Review the slides and simulation examples again to identify the concepts that you may have missed.
-
Congratulations, you have passed the quiz!
You scored better than average, but if you are still unsure about a particular topic, try starting a discussion on the Ansys Learning Forum to discuss your questions with peers around the world.
-
Congratulations, you have passed the quiz!
You did great - Check out other courses to further your knowledge. Also, visit the Ansys Learning Forum and participate in discussions on this subject to help your peers and deepen your own knowledge.
-
Congratulations you have passed the quiz!
You have excelled on this topic - Check out other courses and see if you can ace them too. Also, visit the Ansys Learning Forum to help your peers on this topic. With your knowledge, you can make a real difference.
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- Current
- Review
- Answered
- Correct
- Incorrect
-
Question 1 of 10
1. Question
What is the maximum equivalent stress under the applied load? Select the option that is closest to the correct result.
CorrectIncorrect -
Question 2 of 10
2. Question
Review the reaction forces of the supports at holes A and B. Based on the applied load, what percentage of the force is reacting through hole A along the same direction? Select the option that is closest to the correct result.
CorrectIncorrect -
Question 3 of 10
3. Question
What is the appropriate object to utilize to indicate the half-symmetry nature of this model in Mechanical? Select the best option below.
CorrectIncorrect -
Question 4 of 10
4. Question
Imagine that the material of the bracket is changed to aluminum, which has an elastic modulus of almost a third that of steel. (Do not re-run the simulation with different material properties.) Select the two best options below that are correct statements.
CorrectIncorrect -
Question 5 of 10
5. Question
Identify which of the Degrees of Freedom of the nodes located on the symmetry region are constrained for the model?
CorrectIncorrect -
Question 6 of 10
6. Question
What is the minimum Factor of Safety per the von Mises Theory of Failure for the given condition, using the tensile yield strength of the material? Select the option closest to the correct result.
CorrectIncorrect -
Question 7 of 10
7. Question
What is the maximum total deformation obtained under the given load? Select the option that is closest to the correct result.
CorrectIncorrect -
Question 8 of 10
8. Question
Which of the following supports could be used at locations A and B based on the problem description? Select the two best options.
CorrectIncorrect -
Question 9 of 10
9. Question
Consider the same case but with an additional requirement that the self-weight of the bracket needs to be considered in the analysis. Gravity is assumed to be acting in the negative y-direction of the model. The model must be solved using the same half-symmetry conditions. Select the best option below that is a correct statement.
CorrectIncorrect -
Question 10 of 10
10. Question
Consider the following locations in the figure below. Which location is closest to the location of the peak value of Minimum Principal Stress? Select the best option.
CorrectIncorrect