Course Assessment - Geometry Representation
Quiz Summary
0 of 10 Questions completed
Questions:
Information
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading...
You must sign in or sign up to start the quiz.
You must first complete the following:
Results
Results
0 of 10 Questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 point(s), (0)
Earned Point(s): 0 of 0, (0)
0 Essay(s) Pending (Possible Point(s): 0)
Categories
- Not categorized 0%
-
Unfortunately, you did not pass the quiz.
Don't be discouraged - Go through the course material including the lecture videos, handout slides, and simulation examples to prepare and try again.
-
Congratulations, you have passed the quiz!
You still have room for improvement - Review the slides and simulation examples again to identify the concepts that you may have missed.
-
Congratulations, you have passed the quiz!
You scored better than average, but if you are still unsure about a particular topic, try starting a discussion on the Ansys Learning Forum to discuss your questions with peers around the world.
-
Congratulations, you have passed the quiz!
You did great - Check out other courses to further your knowledge. Also, visit the Ansys Learning Forum and participate in discussions on this subject to help your peers and deepen your own knowledge.
-
Congratulations you have passed the quiz!
You have excelled on this topic - Check out other courses and see if you can ace them too. Also, visit the Ansys Learning Forum to help your peers on this topic. With your knowledge, you can make a real difference.
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- Current
- Review
- Answered
- Correct
- Incorrect
-
Question 1 of 10
1. Question
Before performing a finite element simulation, a decision should be made regarding how much geometry to include in the analysis. What are the factors that influence this decision? Select the 2 best options.
CorrectIncorrect -
Question 2 of 10
2. Question
In Discovery, when "Exclude from Simulation" option is used with any geometry, it means that ____. Select the best option to complete this sentence.
CorrectIncorrect -
Question 3 of 10
3. Question
Consider a crane lifting a heavy load on its hook. Let us assume that only the crane's hook has been identified as a point of failure in the past. If we are interested in the stress distribution of the crane's hook, which of the following statements are TRUE? Select the 2 best options.
CorrectIncorrect -
Question 4 of 10
4. Question
The slenderness ratio is defined as $\frac{GAL^2}{EI}$, where G is the shear modulus, A is the cross-sectional area, L is the length, and E is the elastic modulus, and I is the area moment of inertia. Which of the following options is a suitable general guideline that can be used to determine if a segment can be represented with a beam or line body? Select the best option.
CorrectIncorrect -
Question 5 of 10
5. Question
To post-process the beam section result quantities, we need to go to the Details view of the Solution branch and set the option _____. Select the best option that completes the statement.
CorrectIncorrect -
Question 6 of 10
6. Question
Which of the following is TRUE when using the "Beam Tool" in Ansys Mechanical? Select the best option.
CorrectIncorrect -
Question 7 of 10
7. Question
Which of the following statements are TRUE regarding shell elements? Select the two best options.
CorrectIncorrect -
Question 8 of 10
8. Question
In Ansys Mechanical, which of the following are special result outputs available for surface bodies (shell elements) but not solid bodies? Select the two best options.
CorrectIncorrect -
Question 9 of 10
9. Question
Which of the following statements are TRUE with regards to a 2D Plane Stress Analysis? Select the two best options.
CorrectIncorrect -
Question 10 of 10
10. Question
_____ can solve the structural response, even if there may be some deformation or loading along the fiber direction. Select the best option that completes the statement.
CorrectIncorrect