Ansys Learning Forum › Forums › Installation and Licensing › Ansys Products › Writing Injection files for DPM › Reply To: Writing Injection files for DPM

July 11, 2023 at 4:04 pm
Salix Bair
Subscriber

So I realize that I was mixing my injection formats, I'm pretty sure I have the spacing and formatting correct now: 

(z=4 12)
(x y z u v w diameter t mass-flow mass frequency time name)
(1.0000e-02 6.0000e-04 0.0000e+00 2.0000e+00 0.0000e+00 0.0000e+00 1.0000e-08 3.0000e+02 1.0000e-20 5.2266e-22 1.9133e+01 0.0000e+00 r=1mm:0)
(1.0000e-02 6.0000e-04 0.0000e+00 2.0000e+00 0.0000e+00 0.0000e+00 1.0000e-08 3.0000e+02 1.0000e-20 5.2266e-22 1.9133e+01 0.0000e+00 r=1mm:1)
(1.0000e-02 6.0000e-04 0.0000e+00 2.0000e+00 0.0000e+00 0.0000e+00 1.0000e-08 3.0000e+02 1.0000e-20 5.2266e-22 1.9133e+01 0.0000e+00 r=1mm:2)
(1.0000e-02 6.0000e-04 0.0000e+00 2.0000e+00 0.0000e+00 0.0000e+00 1.0000e-08 3.0000e+02 1.0000e-20 5.2266e-22 1.9133e+01 0.0000e+00 r=1mm:3)

I'm still getting an error when I try to read it in. 

I also tried: 

(z=4 12)
( x  y  z  u  v  w  diameter  t  mass-flow  mass  frequency  time  name)
( 1.0000e-02  6.0000e-04  0.0000e+00  2.0000e+00  0.0000e+00  0.0000e+00  1.0000e-08  3.0000e+02  1.0000e-20  5.2266e-22  1.9133e+01  0.0000e+00  r=1mm:0)
( 1.0000e-02  6.0000e-04  0.0000e+00  2.0000e+00  0.0000e+00  0.0000e+00  1.0000e-08  3.0000e+02  1.0000e-20  5.2266e-22  1.9133e+01  0.0000e+00  r=1mm:1)
( 1.0000e-02  6.0000e-04  0.0000e+00  2.0000e+00  0.0000e+00  0.0000e+00  1.0000e-08  3.0000e+02  1.0000e-20  5.2266e-22  1.9133e+01  0.0000e+00  r=1mm:2)
( 1.0000e-02  6.0000e-04  0.0000e+00  2.0000e+00  0.0000e+00  0.0000e+00  1.0000e-08  3.0000e+02  1.0000e-20  5.2266e-22  1.9133e+01  0.0000e+00  r=1mm:3)