Simulation Exercise - Harmonic Analysis in Ansys Mechanical
Download the zip file and extract the contents. Go through the Instructions file. Follow along with the provided steps and solve the model. You can start the quiz after you have obtained a solution.
For performing the simulation, you can use the latest release of the academic, commercial or free student version of Ansys Mechanical. Download Ansys Student for free here.
Quiz Summary
0 of 10 Questions completed
Questions:
Information
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading...
You must sign in or sign up to start the quiz.
You must first complete the following:
Results
Results
0 of 10 Questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 point(s), (0)
Earned Point(s): 0 of 0, (0)
0 Essay(s) Pending (Possible Point(s): 0)
Categories
- Not categorized 0%
-
Unfortunately, you did not pass the quiz.
Don't be discouraged - Go through the course material including the lecture videos, handout slides, and simulation examples to prepare and try again.
-
Congratulations, you have passed the quiz!
You still have room for improvement - Review the slides and simulation examples again to identify the concepts that you may have missed.
-
Congratulations, you have passed the quiz!
You scored better than average, but if you are still unsure about a particular topic, try starting a discussion on the Ansys Learning Forum to discuss your questions with peers around the world.
-
Congratulations, you have passed the quiz!
You did great - Check out other courses to further your knowledge. Also, visit the Ansys Learning Forum and participate in discussions on this subject to help your peers and deepen your own knowledge.
-
Congratulations you have passed the quiz!
You have excelled on this topic - Check out other courses and see if you can ace them too. Also, visit the Ansys Learning Forum to help your peers on this topic. With your knowledge, you can make a real difference.
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- Current
- Review
- Answered
- Correct
- Incorrect
-
Question 1 of 10
1. Question
From the Harmonic Response Analysis, what is the frequency at which peak amplitude is observed? Select the option that is closest to the result you obtained.
CorrectIncorrect -
Question 2 of 10
2. Question
Looking at the Directional Deformation results, which location of the mount undergoes maximum deformation? Select the best option.
CorrectIncorrect -
Question 3 of 10
3. Question
In Harmonic analysis, which type of load correctly represents the loading on the DC motor? Select the best option.
CorrectIncorrect -
Question 4 of 10
4. Question
Looking at the Equivalent Stress results, which location of the mount reports maximum stress? Select the best option.
CorrectIncorrect -
Question 5 of 10
5. Question
If the mount was made up of Structural Steel, what would be the effect on the natural frequencies of the mount? Choose the best option without rerunning the model.
CorrectIncorrect -
Question 6 of 10
6. Question
Which of the following linked systems correctly represents Harmonic Analysis using Mode Superposition method? Choose the best option.
CorrectIncorrect -
Question 7 of 10
7. Question
If the frequency range in Harmonic analysis was extended up to 1000 Hz, how many natural frequencies would have been considered? Choose the correct option without rerunning the model.
CorrectIncorrect -
Question 8 of 10
8. Question
If the Frequency Response chart does not show any peak amplitude, what does it indicate? Select the two best options.
CorrectIncorrect -
Question 9 of 10
9. Question
In the DC motor mount case, if more than 6 modes were extracted in Modal analysis, what would be the effect on the results of Harmonic Analysis assuming all other parameters are kept unchanged? Choose the correct option without rerunning the model.
CorrectIncorrect -
Question 10 of 10
10. Question
For the Directional Deformation results, select the correct statement for the Sweeping Phase Angle.
CorrectIncorrect