Quiz - Convection Copy | ANSYS Innovation Courses

Quiz Summary

0 of 13 Questions completed

Questions:

You have already completed the quiz before. Hence you can not start it again.

Quiz is loading...

You must sign in or sign up to start the quiz.

You must first complete the following:

Results

Quiz complete. Results are being recorded.

Results

0 of 13 Questions answered correctly

Your time:

You have reached 0 of 0 point(s), (0)

Current
Review
Answered
Correct
Incorrect

Question 1 of 13

1. Question
For the gingerbread homework problem, by which method, the gingerbread can be cooled down faster?
- 1. Put the gingerbread in the fridge
- 2. Put the gingerbread in room temperature and use a fan to blow on it
- 3. The two methods use the same time to cool down the gingerbread
Correct

Incorrect
Question 2 of 13

2. Question
Convection cannot occur in:
- 1. Solids
- 2. Gases and Liquids
- 3. Fluids
- 4. None of the above
Correct

Incorrect
Question 3 of 13

3. Question
For the water-cooled heat sink homework, what’s the difference of maximum temperature on the heat sink between the model with water cooling and without water cooling?
- 1. Around 58 degree Celsius
- 2. Around 25 degree Celsius
- 3. Around 12 degree Celsius
- 4. Same maximum temperature for the two models
Correct

Incorrect
Question 4 of 13

4. Question
Which of the following statement is correct?
- 1. Diffusion and advection cannot occur simultaneously
- 2. Diffusion of mass is caused by heat gradient
- 3. Diffusion of heat is caused by concentration gradient
- 4. None of the above 
Correct

Incorrect
Question 5 of 13

5. Question
Film coefficient may be obtained by:
- 1. Analytical solution for some simple cases
- 2. Carefully designed experiments
- 3. Numerical solution from a CFD analysis
- 4. All of the above
Correct

Incorrect
Question 6 of 13

6. Question
Which of following has the same principle of heat conduction?
- 1. Advection
- 2. Diffusion of mass
- 3. Diffusion of heat
- 4. Natural convection
Correct

Incorrect
Question 7 of 13

7. Question
Which of the following statements about film coefficient is true?
- 1. For natural convection, film coefficient for water is higher than air
- 2. It can be thought of as the heat flux needed to cause a unit difference in temperature in a unit volume
- 3. It has the same unit as thermal conductivity
- 4. It is an important input in a CFD analysis
Correct

Incorrect
Question 8 of 13

8. Question
Which of following statement is correct about natural and forced convection?
- 1. Usually engineers don’t need to consider natural convection as it occurs naturally.
- 2. Usually forced convection is more efficient than natural convection in heat transfer.
- 3. Forced convection and natural convection cannot exist at the same time.
- 4. Forced convection is only used for dissipation of heat, not to increase of temperature.
Correct

Incorrect
Question 9 of 13

9. Question
For the water-cooled heat sink homework problem, which statement is true?
- 1. Thermal fluid line element is an accurate way to calculate the fluid temperature but adds significant computational cost
- 2. With the water cooling, no more convection boundary condition is needed on the fin surfaces since they are negligible
- 3. The underlining body of the heat sink should be explicitly modeled
- 4. None of the above
Correct

Incorrect
Question 10 of 13

10. Question
When solving the heat transfer simulation by conduction-based solver, which of the following statement is correct?
- 1. The governing equation of fluid dynamics is solved.
- 2. Convection flow (the direction of convection) can be obtained.
- 3. Conduction-based solver is considered as more accurate than fluid dynamics solver.
- 4. Convection is simulated as a boundary condition with two parameters: film coefficient and bulk temperature.
Correct

Incorrect
Question 11 of 13

11. Question
Film coefficient can be affected by:
- 1. Viscosity of the fluid
- 2. Velocity of the fluid
- 3. Temperature of the fluid
- 4. All of the above
Correct

Incorrect
Question 12 of 13

12. Question
Which of the following statement of bulk temperature is incorrect?
- 1. Bulk temperature represents the average temperate of the fluid.
- 2. Bulk temperature can be higher or lower than the surface temperature.
- 3. Bulk temperature is always a fixed value inputted by engineers.
- 4. None of the above.
Correct

Incorrect
Question 13 of 13

13. Question
To use thermal-flow fluid line element, which of the parameter should be known?
- 1. The speed of the fluid flow
- 2. The inlet fluid temperature
- 3. Convection film coefficient between the surface and the fluid
- 4. All of the above
Correct

Incorrect

Quiz - Convection Copy

Quiz - Convection Copy

Quiz Summary

Information

Results

Results

Categories

1. Question

2. Question

3. Question

4. Question

5. Question

6. Question

7. Question

8. Question

9. Question

10. Question

11. Question

12. Question

13. Question